Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 497 / 535

8-7

ZJ157A

2. Install the steering tie rod to the steering post and

secure with new lock nut. Tighten to 35 ft-lb.

ZJ156A

3. Secure the bearing bracket/steering post assembly to

the upper support plate with the bracket plates and

cap screws (coated with blue Loctite #243). Tighten

the cap screws to 96 in.-lb.

FS182A



NOTE: When installing the bracket plates, the wider

end of the plate must be directed up.

FS200A

4. On the Bearcat 570/F-Series/T-Series, place the rub-

ber exhaust bumper into position on the air silencer.

FS203A

5. On the Bearcat/F-Series/T-Series, place gaskets on

the resonator and exhaust manifold; then install the

expansion chamber. Secure the chamber to manifold

and upper frame with the springs.

6. On the standard models, place the handlebar/adjuster

block onto the steering post; then secure the handle-

bar to the steering post with the adjuster caps, four

cap screws, and lock nuts. Tighten cap screws

securely.

7. On the non-turbo TZ1/Z1, install the front end close-

off cover; then with the exhaust pipe mounting tab

(B) installed to the right-side cap screw, tighten the

cap screws (A) securely.

ZJ020A

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды