Arctic Cat Sno Pro 120 2011 страница 531 Скачать руководство пользователя

Страница: 531 / 535

8-41

REMOVING BUMPER/SNOWFLAP



NOTE: The snowflap can be removed without

removing the bumper by removing the four torx-head
cap screws and lock nuts.

1. Remove the four torx-head cap screws and lock nuts

securing the bumper assembly to the running board;

then remove the four lock nuts from under the tun-

nel. Account for the U-nuts and cap screws.

2. Slide the bumper off the tunnel.

3. Remove the four torx-head cap screws securing the

snowflap to the tunnel. Account for cap screws,

washers, and lock nuts.

INSTALLING BUMPER/SNOWFLAP

1. Secure the snowflap to the tunnel with the cap

screws, washers, and lock nuts taking care to place

the washers next to the underside of the snowflap.

Finger-tighten the cap screws to the lock nuts; then

tighten the cap screws to 20 ft-lb.

2. Place the bumper assembly into position on the tun-

nel and secure to the running boards with the torx-

head cap screws; then from under the tunnel, install

the four lock nuts and tighten to 20 ft-lb.

Tunnel/Chassis/Rear

Bumper/Snowflap

(Bearcat 570/T-Series)

REMOVING BUMPER SNOWFLAP

1. Remove the four torx-head cap screws, lock nuts,

and washers securing the snowflap to the tunnel.

2. Remove the right- and left-side rear fenders; then

carefully drill out the rivets from the back side of the

tunnel.

INSTALLING BUMPER SNOWFLAP

1. Install the rear bumper and with the holes properly

aligned, secure the bumper to the tunnel with rivets;

then install and secure the rear fenders.

2. With the snowflap support in place, install the snow-

flap and secure with the torx-head cap screws, wash-

ers, and lock nuts.

Tunnel/Chassis/Rear

Bumper/Snowflap

(CFR/Crossfire/M-Series)

REMOVING/REPLACING TUNNEL

To remove and/or replace a tunnel on a particular snow-

mobile, a number of removing and installing component

sequences must be followed. The technician must in turn

go to the following sections in this manual and refer to

the appropriate removing/installing sub-sections. When

doing these sequences, the technician should use discre-

tion and sound judgment.

A. Section 2 - Engine

B. Section 6 - Drive Train/Track/Brake Systems

C. Section 7 - Rear Suspension

D. Section 8 - Steering and Body

REMOVING BUMPER/SNOWFLAP

1. Drill out the rivets securing the snowflap to the tun-

nel end cap; then disconnect the taillight harness

connector. Remove the snowflap/taillight.

0743-320

2. Remove the two self-tapping screws securing the

taillight to the snowflap.

3. Carefully drill the rivets from the back side of the

tunnel securing the bumper to the tunnel. Remove

the bumper.

INSTALLING BUMPER/SNOWFLAP

1. Secure the rear bumper to the tunnel with the appro-

priate-length rivets.

2. Secure the taillight to the snowflap with the two self-

tapping screws; then connect the taillight connector.

3. Secure the snowflap to the tunnel end cap with riv-

ets.

CAUTION

Use caution when drilling the rivets from the rear bum-
per and snowflap not to damage the heat exchangers.

CAUTION

Use caution when drilling the rivets from the rear bum-
per and snowflap not to damage the heat exchangers.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды