manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Сервисный мануал Arctic Cat Sno Pro 120 2011 доступен для бесплатного скачивания на {вашем сайте}. Этот руководство поможет вам поддерживать и обслуживать ваш снегоход, обеспечивая надежную работу. Скачайте его прямо сейчас и получите всю необходимую информацию для правильного ухода за вашим транспортным средством.

Поделиться
Скачать
background image

7-119

7

FS010

21. Slide bearing assembly off of shaft.

22. Remove the bleed screw from the bearing and set

them both on a clean, lint-free towel.

REBUILDING

1. Using a pair of snap ring pliers, remove the snap ring

from the bearing housing. Using fingers, remove the

FIST scraper from the housing. Using a scribe,

remove the O-ring from the inside of the FIST

scraper by “spearing” the seal with the point of the

scribe and pulling it out.

FS011

2. Using a scribe, remove the U-cup wiper and O-ring

seals from the bearing housing. 

3. Thoroughly clean the FIST bearing, bearing housing,

and piston assembly with solvent. Dry with com-

pressed air in a well ventilated area.

4. Using a scribe, remove the O-ring seal from the IFP.

5. Install the new, well lubricated O-ring into the FIST

bearing. Check to make sure the O-ring is properly

seated and is not twisted. 

NOTE: To aid in proper seating of the O-ring, it may

be advisable to use a soft, blunt object (non-writing
end of a pen, etc.) to push it in.

6. Install the new, well lubricated O-rings into the bear-

ing housing making sure the shaft O-ring is in the

groove next to the DU bushing and that the O-rings

are properly seated and not twisted. It may be advis-

able to use a soft, blunt object to push it in.

7. Install the new U-cup seal into bearing. U-cup

should be installed so the cupped end is facing the

DU bushing inside of bearing. Check to make sure

seal is properly seated. It may be advisable to use a

soft, blunt object to push it in. 

8. Install FIST bearing into housing. Check for proper

orientation of the FIST bearing. The stepped side of

the FIST bearing should be visible. 

9. Using a pair of snap ring pliers, install the snap ring

into the bearing housing. Check for proper orienta-

tion of the snap ring. The flat side of the snap ring

should be visible. Check to make sure the snap ring

is properly seated.

FS007

10. Install the new, well greased O-ring onto the IFP.

11. Replace the bearing bleed screw O-ring. 

ASSEMBLING

1. Clamp shaft eyelet securely in vise and place a seal

tool on end of shaft. 

2. Lubricate the bearing assembly seals with an assem-

bly lube. Slide the bearing assembly onto shaft with

the FIST bearing facing the eyelet. This should be

done in a single smooth motion to avoid damaging

the seals.

3. Hold the piston assembly from underneath the top-

out plate and place the end of the screwdriver onto

the end of the shock shaft. Slide the piston assembly

onto the shaft end. Check to make sure the piston

assembly is seated properly and install the piston

lock nut. Tighten nut to 18 ft-lb. Remove shaft

assembly from vise and set it aside on a clean, lint-

free paper towel.

CAUTION

Use care when passing the bearing over the shaft
threads not to scratch the inside of the bearing
assembly.

CAUTION

Care must be taken when using a scribe to remove a
seal. Always spear the seal with the point of the
scribe. Do not attempt to wedge the scribe behind the
seal as this could cause damage to the seal groove
and compromise the performance of the shock.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Yeti SnowMX 2021 User Manual preview
SnowMX 2021
Бренд: Yeti Страницы: 83

Бренды по названию

Популярные бренды

Загрузить еще бренды