Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 248 / 535

4-22

ZJ018A

ZJ289A

2. Loosen the throttle cable jam nut; then remove the

throttle cable from the bracket and the throttle valve

cam.

ZJ103A

3. Remove the cable ties securing the fuel injector wir-

ing harness to the fuel rail; then disconnect the har-

ness from the fuel injectors.



NOTE: For installing purposes, note the location of

all cable ties.

ZJ094D

4. Loosen the clamps securing the throttle bodies to the

intake boots; then remove the throttle body assembly.

5. Remove the retaining clips securing the fuel rail to

the injectors; then remove the two screws securing

the fuel rail to the throttle body assembly. Remove

the fuel rail and injectors from the throttle body

assembly.

ZJ290



NOTE: For assembling purposes, note from which

side the fuel injectors were removed.

6. Remove the two screws securing the ISC valve; then

remove the valve from the throttle body assembly.

ZJ131A



NOTE: For assembling purposes, note the color-

marks on the throttle body assembly and ISC valve.
Also, note the different-size screws.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды