Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 337

Страница: 337 / 535

6-14

ZJ211

12. Using the Rear Suspension Spring Tool, remove the

spring from the adjusting cam.

13. On the F-Series/T-Series, remove the rear cap screws

securing the skid frame to the tunnel; then slide the

skid frame rearward far enough to drop the front arm

out of the slider axle and remove the skid frame.

Account for lock washers and flat washers.

14. On the remaining models, remove all four cap

screws and lock nuts (if applicable); then remove the

skid frame.

15. With the gear case and skid frame removed, pull the

driveshaft toward the gear case side of the tunnel

until it clears the brake caliper housing; then remove

the driveshaft. Account for the rubber seal.

ZJ212



NOTE: The brake disc can remain locked in the

brake caliper unless being serviced.



NOTE: At this point if necessary, remove the track.

INSTALLING TRACK DRIVESHAFT/
GEAR CASE



NOTE: At this point if the track was removed, install

the track.



NOTE: Steps 1-8 are for installing the track drive-

shaft. If only installing the gear case, proceed to step
9.



NOTE: Prior to installing the driveshaft, apply a coat

of Anti-Seize Thread Compound to the internal
splines of the driveshaft.

ZJ213A

1. If the brake disc was removed, place the track/drive-

shaft assembly into the bearing of the brake housing

just far enough to allow the brake disc to be installed

in the brake housing assembly.

ZJ214A



NOTE: Prior to installing the driveshaft, ensure the

driveshaft sleeves are centered to the inner bore of
the brake caliper housing.

ZJ307A

2. With the brake lever lock engaged and the brake disc

correctly positioned in the brake housing assembly,

properly align the splines of the driveshaft with the

brake disc; then push the driveshaft the rest of the

way into the brake housing until properly seated.

! WARNING

Care must be taken when removing the spring or dam-
age or injury could result.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 337 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: