Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 459 / 535

7-91

4. Inspect the cap screw for cracked, stretched, or dam-

aged threads. Use a new lock nut when assembling.

INSTALLING

1. Position the end cap on the slide rail; then align the

hole in the end cap with the hole in the slide rail.

2. Secure with a cap screw, washers, and lock nut.

Tighten to 80 in.-lb.

Shock Pads



NOTE: The skid frame does not have to be removed

for this procedure.

REMOVING



NOTE: The shock pads should be removed only if

being replaced.

1. Using a 3/16-in. drill bit, drill out the rivets securing

each front shock pad to the slide rail. Account for the

retaining brackets.

2. Remove the torx-head screws and lock nuts securing

the rear shock pads to the slide rail; then remove the

shock pads.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the pad and retaining brackets for damage or

wear.

2. Inspect the rivet holes in the slide rail for damage or

elongation.

INSTALLING

1. Place the front pads and retaining brackets into posi-

tion on the slide rail; then secure with rivets.

2. Place the rear pads into position on the slide rails;

then secure with the torx-head screws and lock nuts.

Tighten securely.

Idler Wheels/Mounting

Blocks



NOTE: The skid frame does not have to be removed

for this procedure.

REMOVING

1. Remove the cap screw and lock nut securing the idler

wheel to the idler wheel mounting block; then

remove the cap screw and lock nut securing the

mounting block to the slide rail.

TZ024A

MS003A

2. Account for a flat washer from the idler wheel cap

screw.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Clean the bearing with a clean cloth.

2. Inspect each idler wheel for cracks or damage.

3. Rotate the idler wheel bearing (by hand) and inspect

for binding or roughness.

4. If a bearing must be replaced, use this procedure.



NOTE: If the idler wheel has no snap ring securing

the bearing, the idler wheel is not serviceable.

A. Remove the bearing snap ring.

B. Using a hydraulic press or suitable driving tool,

remove the bearing from the inside of the wheel.

C. Press the new bearing (on its outer race) into the

idler wheel.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды