Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 184 / 535

3-5



NOTE: When installing the lower check valve,

assure that the washer gaskets are installed on each
side of the valve.

FS235A

10. Place the impeller into position and secure with a cap

screw and washer. Be sure the rubber side of the

washer is lubricated with a fine coat of oil and

directed towards the impeller. Apply blue Loctite

#243 to the threads of the cap screw and tighten to

108 in.-lb.

FC132

11. Apply sealant to the crankcase seam; then install the

alignment pins into the crankcase (if removed).

FC133A



NOTE: Do not allow sealant into the breather hole in

the crankcase. If sealant gets into the hole, carefully
remove before proceeding.

FC072B

12. Position the O-ring into the water pump cover; then

install the cover. Install the cap screws; then using

the pattern shown, tighten to 96 in.-lb.

FC134

0742-304

Water Pump

(800/1000 cc)

DISASSEMBLING



NOTE: The engine must be removed for this proce-

dure (see Section 2).



NOTE: A bleed hole is located in the crankcase

beneath the water pump housing. If any signs of
coolant leakage from the bleed hole exist, the water
pump seals must be replaced.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды