Arctic Cat Sno Pro 120 2011 страница 522 Скачать руководство пользователя

Страница: 522 / 535

8-32

FC227

INSTALLING

1. Place the console into position; then secure the con-

sole with the torx-head screws.

FC227

2. Connect the wiring harness to the ignition switch.

3. Thread the recoil starter rope through the console

and handle. Tie a knot at the end of the recoil rope.

Seat the cap. Remove the slip-knot and allow the

rope to retract.

Console (Bearcat/F-Series/

T-Series/Z1)

REMOVING

1. Remove the two torx-head screws securing the con-

sole to the chassis; then lift up the rearward end of

the console and disconnect the console harness plug-

in.

0743-777

2. Remove the console.

INSTALLING

1. Place the console into position on the headlight sup-

port bracket; then connect the console harness con-

nector.

2. Secure the console to the chassis with the two torx-

head screws.

Front Bumper/Belly Pan

Assembly

(CFR/Crossfire/M-Series)

REMOVING

1. Remove the hairpin clip and torx-head cap screws

securing the side panels; then remove the panels.

2. Remove the cable tie and remove the air intake con-

nector from the air silencer.

3. Remove the screws securing the hood cables to the

chassis; then with the hood secured, remove the hair-

pin clips from the hood pins.

SC067A

4. Remove the pins securing the hood to the front bum-

per and remove the hood.

5. Disconnect the exhaust temperature sensor (600/800/

1000 cc) from the expansion chamber; then remove

the resonator and expansion chamber. Account for

the seven exhaust springs, hairpin clip, and tab

washer.



NOTE: Step 6 is only necessary if the right-side

belly pan is being replaced.

6. Remove the torx-head cap screws and lock nuts

securing the regulator/rectifier to the right-side belly

pan; then remove the cap screws securing the ECU to

the air silencer. Secure the components out of the

way.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды