Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 290 / 535

5-29

2. Remove the four screws securing the left-side han-

dlebar control assembly; then remove the control

assembly from the handlebar.

3. Disconnect the handlebar/thumb warmer harness

from the switch.

4. With the thumb warmer toggle in the low position,

connect one ohmmeter lead to pin (C) and the other

ohmmeter lead to pin (B). The meter must read 1

ohm or less resistance.

CM110A

5. With the thumb warmer toggle in the high position,

connect one ohmmeter lead to pin (C) and the other

ohmmeter lead to pin (A). The meter must read 1

ohm or less resistance.



NOTE: If either test does not read within specifica-

tion, replace the complete control assembly.

6. With the handwarmer toggle in the low position,

connect one ohmmeter lead to pin (C) and the other

ohmmeter lead to pin (D). The meter must read 1

ohm or less resistance.

7. With the handwarmer toggle in the high position,

connect one ohmmeter lead to pin (C) and the other

ohmmeter lead to pin (E). The meter must read 1

ohm or less resistance.



NOTE: If either test does not read within specifica-

tion, replace the complete control assembly.

INSTALLING

1. Connect the handlebar/thumb warmer harness to the

switch; then place the control assembly on the han-

dlebar.

2. Secure with the four screws; then install the handle-

bar pad.

Testing Passenger

Handwarmer Switch

1. Disconnect the lead wires from the switch.

2. With the switch in the LO position, connect one

ohmmeter lead to the green/white wire at the connec-

tor; then connect the other ohmmeter lead to the

brown wire at the connector. The meter must read

less than 1 ohm of resistance.

3. With the switch in the MED position, connect one

ohmmeter lead to the green/red wire at the connec-

tor; then connect the other ohmmeter lead to the

brown wire at the connector. The meter must read

less than 1 ohm of resistance.

4. With the switch in the HI position, connect one ohm-

meter lead to the green/blue wire at the connector;

then connect the other ohmmeter lead to the brown

wire at the connector. The meter must read less than

1 ohm of resistance.

Testing Passenger

Handwarmer Elements



NOTE: During this test, resistance will vary due to

temperature; therefore, this test should be made at
room temperature of 20° C (68° F).

1. Disconnect the lead wires from the main wiring har-

ness.

2. For the LO position, connect one ohmmeter lead to

the green/white wire from the element; then connect

the other ohmmeter lead to the green wire from the

element. The meter must read between 23.8-32.2

ohms.

3. For the MED position, connect one ohmmeter lead to

the green/red wire from the element; then connect

the other ohmmeter lead to the green wire from the

element. The meter must read between 13.6-18.4

ohms.

4. For the HI position, connect one ohmmeter lead to

the green/blue wire from the element; then connect

the other ohmmeter lead to the green wire from the

element. The meter must read between 8.7-11.7

ohms.

Testing Seat Heater

Harness/Switches



NOTE: The seat heater elements cannot be tested.

OPERATOR HEATER SWITCH -
Resistance



NOTE: The element connectors are located at the

rear of the front seat beneath the flap.

1. Disconnect the main harness/element connector.

2. Connect one ohmmeter lead to the red/yellow main

harness connector; then connect the other ohmmeter

lead to the green/red main harness connector. The

meter must read the following ± 5%:

4.32K ohms

MED

3.92K ohms

3.57K ohms

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды