Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 472 / 535

7-104

TZ048A



NOTE: At this point, the slide rail should be free of

the skid frame components and can be removed.

TZ049



NOTE: If the shock pad must be replaced, refer to

Shock Pads at the beginning of this procedure.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the slide rail for cracks (A), elongated holes

(B), or unusual bends.

MS220A

2. Inspect the wear strip for wear. The wear strip must

be 0.42 in. thick or thicker. If the wear strip measure-

ment is less than specified, replacement of both wear

strips is necessary.

AG530D

0743-189

3. Inspect the front arm slider bumpers for cracks or

wear.

ZJ284A

INSTALLING

1. With the slide rail assembly on its side, place the slide

rail to the front shock axle, rear arm pivot/idler wheel

assembly, and rear arm cap screws; then secure the

cap screws with lock nuts. Finger tighten only.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды