Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 150

Страница: 150 / 535

2-112

ZJ037A

17. Obtain top-dead-center by rotating the crankshaft

until the arrows on the intake camshaft face (A) are

in the 12 o’clock and 9 o’clock positions and the

arrows on the exhaust camshaft face (B) are in the 12

o’clock and 3 o’clock positions.

741-593A

18. Remove the tension adjuster bolt and washer (A)

from the chain tensioner assembly; then remove the

two cap screws (B) securing the assembly to the

engine. Remove the assembly and account for the

spring and ball.

ZJ038A

19. Remove the cap screws securing the camshaft covers

to the cylinder head; then with the covers removed,

remove the timing chain from the camshaft sprock-

ets. Remove the camshafts from the cylinder head.

ZJ039A

20. Using a magnet, carefully remove the tappets from

the cylinder head.

ZJ050



NOTE: For assembling purposes when removing

the tappets, note the location of the tappet, the valve
from which the tappet was removed, and the shim
number of the tappet.

ZJ051B

21. Remove the six nuts and two cap screws (A) from

outside the cylinder head; then remove the six cap

screws (B) from inside the cylinder head. Remove

the head and account the gasket and two dowel pins.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 150 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: