Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 254 / 535

4-28

3. Secure all wires and hoses with cable ties.

Throttle Cable

REMOVING

1. Loosen the throttle cable adjuster at the bracket.

2. Remove the throttle cable from the pulley on the

throttle body lever shaft.

3. On the 500 cc, remove the E-clip securing the oil-

injection cable to the oil-injection pump control arm.

Account for a washer.

4. On the 500 cc, loosen the oil-injection cable jam

nuts.

5. On the other models, remove the handlebar pad and

the console (if applicable).

6. Remove the cable ties securing the throttle cable.

7. Remove the throttle cable ends from the throttle

lever and from the throttle control housing.



NOTE: Some EFI models are equipped with a con-

trol rod activated oil pump. If it must be removed, the
rod simply snaps off and on at the control arm.

INSTALLING/ADJUSTING

1. Install the throttle cable into the throttle switch

assembly making sure the cable snaps into place.

2. Install the throttle cable end on the throttle lever.

3. Route the throttle cable from the throttle switch

assembly to the throttle body assembly and oil-injec-

tion pump; avoid any sharp bends or moving compo-

nents.

4. Attach the throttle cable to the pulley on the throttle

body shaft.

5. On the 500 cc, install the oil-injection cable adjuster

on the oil-injection pump; secure with the jam nuts.

6. On the 500 cc, install the oil-injection cable on the

control arm; secure with a washer and E-clip.

7. Secure the throttle cable to the handlebar and steer-

ing post with cable ties.

8. On the other models, install the handlebar pad and

the console (if applicable).

9. Adjust the throttle cable tension by turning the jam

nuts in the appropriate direction until 0.030-0.060 in.

free-play exists in the throttle lever and the butterfly

completely opens and closes. Tighten the jam nuts

securely.

741-518A

10. Synchronize the oil-injection pump.

CAUTION

Compress the throttle control lever to ensure free
movement. If the throttle cable sticks or binds, correct
the problem before starting the engine.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды