Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 486

Страница: 486 / 535

7-118

FS006

9. Remove the shaft assembly from the body tube and

place it on a clean, lint-free paper towel.

10. Remove the shock from the vise and pour shock oil

from body tube into a proper disposal container. DO

NOT REUSE OLD SHOCK OIL.

11. Clamp the body cap of the shock securely in vise

with the open end of the body tube pointing up.

12. Loosen and remove the nitrogen valve from the

body.

FS014

13. Remove the shock body from the vise; then invert

the shock body and place it on a folded shop towel

open end down.

14. Using compressed air (NEVER USE HIGH PRES-

SURE NITROGEN), insert the air gun nozzle into

the nitrogen valve port and blow the IFP out of the

shock body and onto the folded shop towel.

FS012

15. Clean the body tube, reservoir tube, and the IFP with

solvent. Dry with compressed air in a well ventilated

area.

16. Set body assembly aside on a clean, lint-free towel.

17. Clamp the shaft eyelet securely in vise with the pis-

ton end up.

18. Remove the piston lock nut from the end of the shaft.

FS008

19. Hold the tip of a screwdriver against the end of shaft;

then hold the piston assembly under the top-out plate

and lift upwards.

FS009



NOTE: Keeping the components in order is critical

for proper performance of the shock absorber. Doing
steps 20-21 properly ensures that proper order is
kept.

20. Slide the piston assembly onto the shaft of the screw-

driver. Pull the screwdriver away from shock shaft

while supporting the piston assembly and set this on

a clean, lint-free towel.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 486 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: