Arctic Cat Sno Pro 120 2011 страница 287 Скачать руководство пользователя

Страница: 287 / 535

5-26

ZJ150A

INSTALLING

1. Place the magneto into position on the cover; then

install and tighten the three cap screws to 84 in.-lb.

With the harness routed properly, install the timing

sensor and harness clamp and tighten to 84 in.-lb.

ZJ149A

ZJ148A

2. With the two dowel pins installed in the engine case,

install the torque limiter (A) and spacer (B); then

install the inner spacer (C), idler gear (D), and outer

spacer (E).

0742-002

3. Install the two alignment pins in the engine for the

magneto cover; then with a new gasket, install the

cover and with the pattern shown, tighten the 18 cap

screws to 84-in.-lb.

741-583A



NOTE: Assure the oil pump seal is in place prior to

installing the magneto cover.

ZJ151A

4. Install the coolant hoses to the water pump, oil

cooler, and separator tank; then secure the hoses with

the clamps.

5. Place the oil tank into position in the chassis and

install the breather hose; then secure with the clamp.

With the hoses routed properly, install the supply/

return oil hoses to the tank; then secure the hoses

with new clamps.



NOTE: Assure the O-rings are properly seated in the

supply/return oil hose fittings.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды