Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 493 / 535

8-3

9. Remove the ignition switch and the torx-head cap

screws and lock nuts securing the console to the gas

tank; then lay the console aside.

10. Remove the cap screw and lock nut securing the

steering tie rod to the steering post. Discard the lock

nut.



NOTE: The expansion chamber must be removed

for this procedure.

CM002A

11. Remove the torx-head cap screws (A) securing the

close-out panel to the steering support; then remove

the two lock nuts (B) from the steering post mount-

ing block.

SC066B

12. Remove the two lower cap screws securing the steer-

ing support to the chassis.

CM004B



NOTE: Removing only the two lower cap screws will

allow the steering support to be moved forward so
the mounting block and steering post can be
removed.

CM005

13. Remove the steering post. Account for all mounting

hardware.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect all welded areas for cracks or deterioration.

2. Inspect the steering post and steering-post retaining

plate for cracks, bends, or wear.

3. Inspect the adjuster caps and mounting block for

cracks or wear.

INSTALLING

1. Carefully slide the steering post into position in the

chassis. Be careful not to hook any wires or hoses.

2. With the steering post in position on the chassis,

install the steering support and mounting blocks to

the gas tank with two lock nuts taking care not to

pinch any wiring.

CM005

3. Tighten the lock nuts to 96 in.-lb; then install the

close-out panel and secure with torx-head cap

screws.

4. Install the two lower cap screws (threads coated with

blue Loctite #243) on each side of the steering sup-

port. Tighten to 20 ft-lb.

CAUTION

Care must be taken not to hook any wires or hoses
when removing the steering post.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды