Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 155 / 535

background image

2-117

2

ATV-1069

Measuring Piston Pin Diameter

Measure the piston pin diameter at each end and in the

center. Measurement must be within 0.8658-0.8661 in.

for the non-turbo and 0.9447-0.9449 for the turbo. If

measurement is not within specifications, the piston pin

must be replaced.

ATV-1070

Installing Piston Rings

1. Install a thin oil ring, oil ring expander, and thin oil

ring in the bottom groove of the piston. Stagger the

end gaps of the upper and lower thin oil rings until

they are on directly opposite sides of the piston.

741-619A

2. Install the #2 compression ring so the letters on the

top surface of the ring face the dome of the piston.

3. Install the #1 compression L-ring into the top groove

with the face of the ring directed upward.

4. Rotate the rings until the ring end gaps are no less

than 90° from one another.

MEASURING CONNECTING ROD
SMALL END BORE INSIDE
DIAMETER

1. Using a small bore gauge, measure the connecting

rod small end bore inside diameter.

2. Measurement must be within 0.866-0.867 in. for the

non-turbo and 0.945-0.946 in. for the turbo.

ZJ057



NOTE: Check piston pin, connecting rod small end

bore, and piston bore for wear or damage paying par-
ticular attention to condition of small end bore bush-
ing. If pin, connecting rod small end bore, or piston
bore is badly worn or damaged, replace pin, connect-
ing rod, or piston.

Cleaning/Inspecting/Measuring

Cylinder Block

1. Wash the cylinder block in parts-cleaning solvent.

2. Check the head gasket surface of the cylinder for dis-

tortion.

3. Using a straightedge and feeler gauge, check surface

at a total of 6 locations. If distortion limit exceeds

0.002 in., machining of the block will be necessary.

ZJ056

CAUTION

Incorrect installation of the piston rings will result in
engine damage.

Manual

Table of Contents

«
...
153
154
155
156
157
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды