Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 431 / 535

7-63

CM246A

2. Place the front arm shock axle assembly into position

on the skid frame making sure the spacers and wash-

ers are properly positioned. Secure with the cap

screw, washer, and a new lock nut. Tighten to 40 ft-

lb.



NOTE: If the front rail support cap screws were

loosened (after step 6 of removing), tighten to 20 ft-
lb.

3. Secure the front outer idler wheel to the idler wheel

mounting block with cap screws, flat washers, and

lock nuts. Tighten to 20 ft-lb.

CM243A

4. Position the front arm with aluminum axle to the

mounting location in the slide rail. Secure with cap

screws. Tighten to 40 ft-lb.

CM248

5. With the serrated axle installed, secure the shock

absorber in the appropriate mounting hole of the

front arm. Secure with a cap screw and lock nut.

Tighten securely.

CM241



NOTE: Do not over-tighten the shock absorber cap

screw as the shock eyelet must be free to pivot.

6. Secure the rear arm shock absorber and shock link to

the pivot arm bracket with cap screws and lock nuts.

Tighten securely.

CM233A

7. Secure the limiter straps with cap screws, washers,

and lock nuts. Tighten to 120 in.-lb.

CM240A

Slide Rails



NOTE: The skid frame must be removed for this pro-

cedure (see Removing Skid Frame in this sub-sec-
tion).

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды