manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Сервисный мануал Arctic Cat Sno Pro 120 2011 доступен для бесплатного скачивания на {вашем сайте}. Этот руководство поможет вам поддерживать и обслуживать ваш снегоход, обеспечивая надежную работу. Скачайте его прямо сейчас и получите всю необходимую информацию для правильного ухода за вашим транспортным средством.

Поделиться
Скачать
background image

4

4-11

4. Rotate the PTO-side carburetor idle speed screw

clockwise until the tachometer reads slightly above

1500 RPM; then rotate the idle speed screw counter-

clockwise to achieve exact 1500 RPM reading. The

piston valves should now be synchronized and the

engine should idle without holding any throttle pres-

sure.

NOTE: If the engine has no ignition spark with the

throttle in the idle position but has proper spark with
the throttle lever slightly compressed, the carburetor
safety switches must be repositioned.

5. Test the throttle control lever by compressing and

releasing it several times. The lever must return to

the idle position quickly and completely.

Throttle Cable

REMOVING

743-705A

1. Loosen the throttle cable adjuster jam nuts.

2. Remove the mixing body tops.

3. Remove the throttle cables from the piston valves.

4. Remove the throttle cables from the mixing body

tops.

5. Remove the handlebar pad and console.

6. Remove the throttle cable end from the throttle lever.

7. Remove the cable from the throttle switch assembly.

NOTE: It may be necessary to remove the PTO-side

carburetor.

8. Remove the E-ring securing the oil-injection cable to

the control arm. Account for a washer.

9. Loosen the jam nut securing the adjustment cable;

then remove the cable from the oil-injection pump.

INSTALLING

1. Route the throttle cable from the throttle switch

assembly to the carburetors and oil-injection pump;

avoid any sharp bends or moving parts.

2. Install the oil-injection adjustment cable on the oil-

injection pump; secure with the jam nuts.

3. Install the oil-injection cable on the control arm;

secure with a washer and E-ring.

NOTE: Install the PTO-side carburetor if removed.

4. Install the throttle cable into the throttle switch

assembly making sure it snaps into place.

5. Install the throttle cable end on the throttle lever.

6. Install the handlebar pad and console.

7. Attach the throttle cable to each throttle valve. The

valve must seat in the groove of the throttle cable

end; then thread the throttle cable into each mixing

body top.

8. Install each piston valve and mixing body top on the

carburetors. Tighten securely; then secure the tops to

the carburetors with the plates.

9. Adjust the carburetors (see ADJUSTING sub-sec-

tion).

10. Synchronize the oil-injection pump (see Related

Items in this section).

Choke Cable

REMOVING

736-596A

1. Bend down the lock tabs locking each brass choke

cable housing on each carburetor.

2. Using a 12-mm wrench, remove each brass choke

cable housing from each carburetor. Account for the

lock tab washers.

3. Remove each brass plunger and spring from the cable

end; then remove each brass choke cable housing.

! WARNING

DO NOT operate the snowmobile when any compo-
nent in the throttle system is damaged, frayed, kinked,
worn, or improperly adjusted. If the snowmobile is
operated when the throttle system is not functioning
properly, personal injury could result.

KEY

1. O-Ring

2. Throttle Cable

3. Jam Nut

4. E-Ring

CAUTION

Compress the throttle control lever to ensure free
movement. If the throttle cable sticks or binds, correct
the problem before starting the engine.

KEY

1. Choke Cable

2. Knurled Nut

3. Choke Lever

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Yamaha VX500SXBC Service Manual preview
VX500SXBC
Бренд: Yamaha Страницы: 84

Бренды по названию

Популярные бренды

Загрузить еще бренды