manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Сервисный мануал Arctic Cat Sno Pro 120 2011 доступен для бесплатного скачивания на {вашем сайте}. Этот руководство поможет вам поддерживать и обслуживать ваш снегоход, обеспечивая надежную работу. Скачайте его прямо сейчас и получите всю необходимую информацию для правильного ухода за вашим транспортным средством.

Поделиться
Скачать
background image

5-2

Electrical Systems

For testing procedures for specific 4-stroke EFI electrical

system components, refer to the Arctic Cat Diagnostic Sys-

tem Manual or to the Laptop Diagnostic Tool.

All tests of the electrical components should be made

using the digital Fluke Model 77 Multimeter. Replace

any component that does not have a test value within

specifications.

NOTE: Whenever using a digital-style tester, “open

(infinite resistance)” denotes an overload and the
meter reading will be OL since the meter is not cali-
brated to register resistance values of that magni-
tude.

NOTE: Always check the appropriate fuse before

testing a component for failure.

NOTE: Some illustrations and photographs used in

this section are used for clarity purposes only and
are not designed to depict actual conditions.

NOTE: Critical electrical specifications can be

found in Section 1 of this manual.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when servicing the electrical systems.

NOTE: Special tools are available from the Arctic

Cat Service Parts Department.

Ignition System (4-Stroke)

NOTE: There must be 0.030-0.060 in. free-play

between the throttle lever and the control housing.

741-518B

TROUBLESHOOTING

1. Remove the spark plugs and visually check their

condition. Replace any fouled plug. Attach the spark

plugs to the high tension leads and ground them to

the engine.

NOTE: Make sure the ignition switch and the emer-

gency stop switch are in the ON position.

2. Crank the engine over and check for spark. If no

spark is present, check to make sure the throttle cable

is properly tensioned. Compress the throttle control

and while holding the throttle control in this position,

crank the engine over and check for spark. If spark is

now present, adjust the throttle cable tension.

3. If no spark is present, the problem is either one or

more of the following:

A. Defective emergency stop switch

B. Defective safety switch in throttle-control hous-

ing

C. Corroded or loose wire connection at the handle-

bar, hood, or main wiring harness

D. Defective ignition switch

NOTE: To check these possible causes, proceed to

the following TESTING sub-section.

Description

p/n

Arctic Cat Diagnostic System Manual

2256-974

Laptop Diagnostic Tool

0744-048

Multi-TPS Test Harness

1686-436

Actuator Test Harness

0644-518

Fluke Model 77 Multimeter

0644-559

MaxiClips

0744-041

Peak Voltage Reading Adapter

0644-307

Starter Assembly Tool

0644-052

Throttle Position Sensor (TPS) Adjustment Tool Kit

3639-891

Test Harness

0686-999

CCU Diagnostic Test Kit

0644-517

CAUTION

Do not ground the spark plug on the cylinder head
cover. The cover is made of magnesium and any con-
tact with spark or electrical arc will severely pit the
surface.

CAUTION

Before checking for spark, place all the engine switches
in the deactivated position. In the event the engine
could be flooded, engage the starter several times to
clear the engine of excess fuel.

CAUTION

Never crank the engine over without grounding the
spark plugs. Damage to coils and/or ECU may result.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

SCORPION 1975 LIL' WHIP Service Manual preview
1975 LIL' WHIP
Бренд: SCORPION Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды