Arctic Cat Sno Pro 120 2011 страница 154 Скачать руководство пользователя

Страница: 154 / 535

2-116



NOTE: If the existing rings will not be replaced with

new ones, note the location of each ring for proper
installation. When installing new rings, install as a
complete set only.

Cleaning/Inspecting Piston Rings

Using a ring-groove cleaning tool, clean carbon from the

ring-grooves. Be sure to position the ring with its tapered

side up.

Measuring Piston-Ring End Gap

(Installed)

1. Place each piston ring in the wear portion of the cyl-

inder. Use the piston to position each ring squarely in

the cylinder.



NOTE: Remove any carbon; then clean the top of

the cylinder bore before inserting the piston rings.

2. Using a feeler gauge, measure each piston-ring end

gap. Acceptable ring end gap must be within the fol-

lowing specifications.

0738-531

Piston Ring/Groove Clearance



NOTE: Before checking, piston grooves must be

clean, dry, and free of carbon.

Fit new piston ring into piston groove and measure clear-

ance between ring and ringland by using feeler gauge.

Measurement must be within the following specifica-

tions. If clearance is out of specification, replace piston.

0738-532

Measuring Piston Skirt/

Cylinder Clearance

1. Measure the cylinder front to back in six places using

a cylinder bore gauge. Record the largest number.

2. Measure the diameter of the corresponding piston at

a point 10 mm from the piston skirt edge at a right

angle to the piston-pin bore. Piston diameter must be

within 3.8568-3.8574 in. for the non-turbo and

3.8574-3.8580 in. for the turbo. Subtract this mea-

surement from the measurement in step 1. Measure-

ment must be within 0.0011-0.0016 in. for the non-

turbo and 0.0006-0.0010 in. for the turbo. If the

determined wear exceeds the limit indicated, the cyl-

inder block must be bored.

GEN-0033

Measuring Piston Pin Bore
Diameter

1. Insert an inside dial indicator into the piston-pin

bore. Take two measurements to ensure accuracy.

2. Piston pin bore must be within 0.8662-0.8664 in. for

the non-turbo and 0.9449-0.9451 in. for the turbo.

CAUTION

Improper cleaning of the ring-grooves by the use of the
wrong type of ring-groove cleaner will result in severe
damage to the piston.

1st Ring

0.0059-0.0138 in.

2nd Ring

0.0118-0.0177 in.

Oil Ring

0.0078-0.0275 in.

1st – Top Ring

0.0059-0.0074 in.

1st – Bottom Ring

0.0008-0.0035 in.

2nd Ring

0.0008-0.0024 in.

Oil Ring

0.0024-0.0059 in.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды