Arctic Cat Sno Pro 120 2011 страница 242 Скачать руководство пользователя

Страница: 242 / 535

4-16

On the 500 cc, the injectors are coded with letters (A-B-

C). When replacement of a fuel injector is necessary, the

injector must be replaced with an injector of the same

code letter.

IO031A

On the 600/800/1000 cc, the injectors are coded with

symbols (







) and are color-coded yellow and green.

When replacement of a fuel injector is necessary, the

injector must be replaced with an injector of the same

code symbol and color.

FS025

FUEL PRESSURE REGULATOR

The fuel pressure regulator is located in the fuel pump.

The fuel pressure regulator maintains the fuel pressure at

a constant specified level.

FUEL PUMP CIRCUIT

The fuel pump and its circuit are provided with current

from the fuel pump coil on the stator.

For this circuit to function correctly, five components must

be properly functioning. Check the following components

before considering the fuel pump assembly to be defective.

A. Fuel pump coil - see coil test procedure.

B. Emergency stop switch and ignition switch

must be ON.

C. Fuel pump - see fuel pump test procedure.

D. Wiring harness and connectors - clean the con-

nectors and test the harness.

E. ECU.

CRANKSHAFT POSITION SENSOR
(1100 cc)

This sensor measures the location in degrees of rotation

of the crankshaft. A 15° resolution exists between sig-

nals. The signal is triggered by the metal rectangles on

the outer surface of the flywheel as they pass by the sen-

sor. The sensor gives the ECU the location of the crank-

shaft at a given point in time. The ECU processes the

information and uses it in many different types of calcu-

lations. For example, the sensor can be used for RPM,

and it can also be used to determine the rate of accelera-

tion of the crankshaft.

CAMSHAFT POSITION SENSOR
(1100 cc)

This sensor tells the ECU which stroke the engine is on.

Because the 4-stroke engine operates on a 720° cycle, the

piston is at TDC twice per cycle - once on the exhaust

stroke and once on the compression stroke.

MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR (1100 cc)

This sensor measures pressure in the intake manifold

when the engine is running. The ECU uses this sensor to

aid in calculating the required fueling. For the base fuel

map, the 1100 cc non-turbo relies on the MAP sensor

only for low throttle openings. After a given throttle

opening is reached, the ECU switches to the TPS sensor

for its main fuel map. The 1100 cc turbo relies entirely on

the MAP sensor and only uses the TPS for its main fuel

map if the MAP sensor should fail. The ECU uses the

MAP sensor for many other calculations, but the base

fuel map is the main one.

WASTEGATE CONRTOL VALVE
(1100 cc Turbo)

The wastegate control valve adjusts the wastegate posi-

tion based on input from the ECU. The wastegate does

not require any input from the ECU to operate at base

boost levels. In areas of operation where the ECU will

allow the turbo to exceed base boost, the wastegate con-

trol valve bleeds some of the pressure that would typi-

cally be used to open the wastegate via the wastegate

diaphragm port on the turbo. By bleeding this pressure,

the wastegate is set at a lower opening thereby allowing

more exhaust gas to pass by the turbine increasing the

boost level.

KNOCK SENSOR (800 cc)

This sensor senses and controls engine knock or detona-

tion. The knock sensor assesses structure borne noise

(vibrations) caused by rapid pressure rises (detonation) in

either cylinder and performs calibration adjustments to

the necessary cylinder via the ECU limiting damage to

internal engine components. Detonation can be caused by

many variables including poor fuel quality, lean operat-

ing conditions, or modified engine components/systems.

CAUTION

Do not replace an injector with one of a different letter.
Severe engine damage may occur.

CAUTION

Do not replace an injector with one of a different code
symbol or letter. Severe engine damage may occur.

500 cc

600/800/
1000 cc

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды