Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 235

Страница: 235 / 535

4-9

5. Thread the brass choke-cable housing into the carbu-

retor making sure the washer is properly positioned

and tighten securely.

TZ104A

6. Connect the safety switch harness connectors to the

main wiring harness.

7. Adjust the carburetors to the initial setting (see

ADJUSTING in this sub-section).

8. Place the console into position on the headlight sup-

port bracket (do not secure the console with the torx-

head screws at this time); then connect the console/

main harness plug-in.

9. With the belt guard secured, start the engine and

warm up to operating temperature; then adjust the

carburetors (if necessary) until proper calibration is

attained.

10. Secure the console to the steering support with the

torx-head screws and tighten the screws securely;

then close the left-side access panel and close the

hood.

ADJUSTING

Choke Cables

1. Be sure the ignition switch key is in the OFF position

and the brake lever lock is set.

2. Loosen the jam nut securing the choke cable

adjuster. Rotate the choke cable adjuster clockwise

until it bottoms against the brass plunger cap.

3. Slowly rotate the choke cable adjuster counterclock-

wise while checking the choke lever for free-play. As

soon as all free-play has been removed from the end

of the lever, stop rotating the adjuster.

4. With free-play removed from the lever, slowly rotate

the choke cable adjuster once again clockwise while

checking the choke cable lever for free-play. Adjust

until 1/8 in. free-play between front bottom edge of

lever and housing is attained. Securely tighten the

adjuster jam nut.

0732-848

5. Repeat steps 3 and 4 on each carburetor.



NOTE: If a carburetor choke cable is adjusted too

tight, the engine will only operate on 1 cylinder at
idle.

Piston Valves



NOTE: The console can be removed for this proce-

dure.



NOTE: The air silencer is a one-piece unit, and the

silencer boots can be removed to access the intake
bores. Remove the boots from the carburetor to
access the piston valves.

1. Rotate each idle speed screw counterclockwise until

all spring tension is removed.

2. Loosen the jam nut securing each throttle cable

swivel adapter; then rotate the swivel adapter clock-

wise until the piston valve bottoms in the piston

valve bore.

3. In turn on each carburetor, place a finger lightly

against the side of the piston valve; then rotate the

carburetor swivel adapter counterclockwise until

slight upward movement of the valve is noted.

4. In turn on each carburetor, place a finger against

either piston valve. Rotate the idle speed screw

clockwise until it contacts the valve.

5. Compress the throttle lever to the full-open position;

then rotate each idle speed screw clockwise 2 com-

plete turns. Release the throttle lever.



NOTE: The throttle control is equipped with a 3-

prong emergency stop switch connector. There must
be free-play between the lever and the control hous-
ing.

CAUTION

Never run the engine with the hood harness discon-
nected or damage to the electrical system will result.

CAUTION

The air silencer and boots must be in position when-
ever the engine is run. If the silencer is removed and
the engine is run, a lean condition will result. There-
fore, DO NOT run the engine when the air silencer is
removed.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 235 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: