Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 124

Страница: 124 / 535

2-86

11. Secure the cylinders (from step 8) by tightening the

cylinder base nuts and cap screws to 44 ft-lb in three

steps using the appropriate pattern shown.

0738-206

0738-220

12. Install the hose clamp onto the cylinder head coolant

hose with the clamp screw directed outward (toward

the PTO-side of the engine).

CM199A

13. Install the coolant hose and secure the hose onto the

cylinder head; then install the coolant bypass hose

onto the head.



NOTE: On the 1000 cc, install the coolant bypass

hoses onto the cylinders.



NOTE: After the coolant hose has been secured to

the cylinder head, secure the cylinder head up and
out of the way of the cylinder to allow the cylinder O-
rings to be installed.

CM191

14. Lubricate the O-rings with a light coat of grease;

then install the two cylinder O-rings on the top of

each cylinder making sure they are correctly posi-

tioned in the grooves.

FC077



NOTE: Lubricating the O-rings with a light coat of

grease will help keep them seated in the grooves of
the cylinder.

15. Place new O-rings onto each of the head cap screws.

Place four of these cap screws (from opposite end of

each other) into the cylinder head. Thread the spark

plugs in part way; then while holding the head above

the cylinder, carefully start all four cap screws while

observing the cylinder O-rings to make sure they

remain in position. Slowly place the head into posi-

tion on top of the O-rings.

CM175



NOTE: On the 800 cc to install the remaining cap

screws, the spark plugs must be removed.

800 cc

1000 cc

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 124 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: