Arctic Cat Sno Pro 120 2011 страница 292 Скачать руководство пользователя

Страница: 292 / 535

5-31

4. With the reverse button pressed in, the meter must

read less than 1 ohm of resistance. With the reverse

button released, the meter must read OL (open).



NOTE: If the meter does not read as specified in

either test, the switch is defective and must be
replaced.

Testing Shift Switch



NOTE: The shift actuator switch is located on the

right-side handlebar control.

1. Disconnect the actuator two-wire connector from the

handlebar control.

2. Connect one ohmmeter lead to the black wire; then

connect the other ohmmeter lead to the white/violet

wire.

3. With the reverse button pressed in, the meter must

read less than 1 ohm of resistance. With the reverse

button released, the meter must read OL (open).



NOTE: If the meter does not read as specified in

either test, the switch is defective and must be
replaced.

Testing Shift Actuator

(500/600/1100 cc)



NOTE: The actuator is located on the gear case

above the left-side footrest.

1. Disconnect the actuator two-wire connector; then

connect Actuator Test Harness onto the harness side

of the connector.

2. Connect one meter lead to the red/blue lead of the

test harness; then connect the other meter lead to the

black/orange wire lead (500/600 cc) or yellow/

orange wire lead (1100 cc) of the test harness.

3. Secure the belt guard into position; then start the

engine.

4. Press the reverse button; there should be a flash of

DC battery voltage indicated on the meter. Release

the reverse button; then again press the reverse but-

ton; there should be a flash of DC battery voltage

indicated on the meter.



NOTE: If the meter indicates a flash of voltage but

the actuator does not function, the actuator is defec-
tive and must be replaced.



NOTE: If the meter does not indicate a flash of volt-

age, troubleshoot the main harness.

CAUTION

Do not run the engine without the belt guard secured
in place.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды