Arctic Cat Sno Pro 120 2011 страница 283 Скачать руководство пользователя

Страница: 283 / 535

5-22

4. Place the positive and negative cables on the starter

motor; then secure with the lock nuts. Tighten

securely.

FS205A

5. Connect the battery cables (positive cable first) to the

battery.

6. Install and secure the resonator and the expansion

chamber.



NOTE: When installing the exhaust manifold

springs, the long hook portion of the spring must be
attached to the exhaust manifold or premature spring
failure will result.



NOTE: To finalize the installing procedure, the air

silencer must be installed. Proceed to the appropriate
Air Silencer sub-section in Section 3.

Starter Motor (4-Stroke)

REMOVING

1. Remove the negative cable from the battery.



NOTE: To remove the starter motor, the air silencer

must be removed. Proceed to appropriate Air
Silencer sub-section in Section 3.

2. Remove cap screw (A) securing the positive cable to

the starter motor; then remove the two cap screws

(B) and remove the starter motor.

ZJ139A

DISASSEMBLING

1. Secure the starter motor in a suitable clamping

device; then remove the two long cap screws from

the starter motor.

ZJ140A

2. For assembling purposes, make alignment marks on

the bearing housing, magnet housing, and brush

assembly.

ZJ152A

3. Remove the bearing housing (A) and the magnet

housing (B) with armature from the brush assembly

(C).

ZJ141A

4. With the armature removed from the magnet hous-

ing, remove snap ring (D) from the armature.

Account for shim (E) and locking plate (F).

5. Using a flat-blade screwdriver, carefully remove the

seal from the bearing housing.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды