Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 130 / 535

2-92

CONNECTING-ROD SMALL END
BORE

1. Insert a snap gauge into each connecting-rod small

end bore; then remove the gauge and measure it with

a micrometer.

AN061

2. The diameter measurement must be within 1.0631-

1.0634 in. for the 800 cc or 1.1418-1.1422 in. for the

1000 cc.

CRANKSHAFT RUNOUT

0742-727

1. Using the V Blocks, support the crankshaft on the

surface plate.



NOTE: The V blocks should support the crankshaft

on the outer bearings.

2. Mount a dial indicator and base on the surface plate.

Position the indicator contact point against the crank-

shaft location point A (PTO-end) from the crankshaft

end. Zero the indicator and rotate the crankshaft

slowly. Note the amount of crankshaft runout (total

indicator reading).



NOTE: For runout location point specifications, see

Crankshaft Runout/Repair Specifications in Section 1
of this manual.

3. Position the indicator contact point against the crank-

shaft location point B (MAG-end) from the crank-

shaft end. Zero the indicator and rotate the

crankshaft slowly. Note the amount of crankshaft

runout (total indicator reading).

FC046

4. Position the indicator contact point against the crank-

shaft at location point C (center). Zero the indicator

and rotate the crankshaft slowly. Note the amount of

crankshaft runout (total indicator reading).

5. If runout exceeds 0.002 in. at any of the checkpoints,

the crankshaft must be either straightened or

replaced.

Assembling



NOTE: The use of new gaskets and seals is recom-

mended when assembling the engine.



NOTE: Prior to assembling the engine, use parts

cleaning solvent and compressed air and thoroughly
clean the threaded holes of the crankcase and cylin-
ders to properly tighten.



NOTE: When the use of a lubricant is indicated, use

Arctic Cat Synthetic APV 2-Cycle Oil.

1. Apply a thin coat of grease to the inner seal lips of

the water pump seal.

2. Using the seal driver, position the inner water pump

shaft seal onto the seal driver and gently tap the seal

down into position.



NOTE: Grease must be applied to the lips of the

inner seal before installation.

MS986A

! WARNING

Always wear safety glasses when drying components
with compressed air.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды