Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 251 / 535

4-25

TZ075B



NOTE: If the snowmobile is in warranty, breaking

the seal on the idle screw jam nut or the Phillips-head
screws on the TPS will void warranty.

6. Loosen the clamps securing the hose to the intake

pipe and throttle body.

TZ085A

7. Remove the four cap screws securing the throttle

body to the intake manifold and account for the

throttle cable support bracket.

TZ109A

8. Remove the four screws securing the ISC valve to

the throttle body.

TZ110A



NOTE: Remove the throttle body ISC valve before

using any type of cleaner to clean the throttle body.

9. Using a throttle body cleaner, spray throttle valve

once and clean the venturi of carbon buildup. A fine

nylon brush may be needed to clean carbon deposits.

AO252

10. Carefully blow-dry the throttle body and be sure that

the ISC valve rubber gasket is properly placed for

assembly.

11. Disconnect the injector harness and remove the hose

from the fuel pressure regulator; then remove the cap

screws securing the fuel rail/injectors to the intake

flange.

TZ111A

CAUTION

Never place the throttle body in cleaning solvent with
the TPS secured to the throttle body or the sensor
must be replaced.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды