Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 456 / 535

background image

7-88

3. Position the front of the skid frame into the tunnel

and engage the front arm with the slider axle in the

tunnel.

0742-187



NOTE: To aid in centering the front arm with the

hole in the tunnel, position the skid frame and track
at a 45° angle to the bottom of the tunnel.

4. Push the rear of the skid frame and the track into the

tunnel.

5. Align the rear arm assembly with the appropriate

hole in the tunnel. Secure the rear arm assembly with

a cap screw, lock washer, and flat washer. AT THIS

TIME, TIGHTEN ONLY UNTIL SNUG.

6. Tip the snowmobile onto the other side; then align

the pivot arm assembly with the appropriate hole in

the tunnel. Secure the rear arm assembly with a cap

screw, lock washer, and flat washer. AT THIS TIME,

TIGHTEN ONLY UNTIL SNUG.



NOTE: Do not install the short legs of the rear

springs onto the adjusting cams at this time.

7. At this time, place the snowmobile to the upright

position; then tighten both rear arm assembly mount-

ing cap screws to 40 ft-lb.

8. Using the Rear Suspension Spring Tool, install the

short legs of the rear springs onto the adjusting cams

making sure the cams are in the same adjustment

positions.

9. Adjust track tension deflection (see Track Tension in

Section 6) and track alignment (see Track Alignment

in Section 6).

CAUTION

After proper track tension and alignment have been
attained, make certain that the rear axle assembly is
tightened to specifications or component damage will
occur.

Manual

Table of Contents

«
...
454
455
456
457
458
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды