Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 209 / 535

3-30

Air Intake Assembly

(CFR/Crossfire/M-Series)

REMOVING

1. Remove the connector clamp securing the intake

connector (hose) to the hood screen (right-side).

FC248

2. With the hood closed, loosen the headlight adjust-

ment knobs.

3. Carefully push the headlight lenses rearward far

enough to remove the torx-head screws securing the

air silencer plenum to the hood.

4. Open the hood; then remove the O-rings securing the

air silencer plenums to the hood and remove the air

silencer plenums.

INSTALLING

1. Press the air silencer plenums into place on the hood

and secure with the O-rings; then close the hood.

2. Carefully push the headlight lenses rearward far

enough to install the torx-head screws. Tighten the

screws securely.

3. Tighten the headlight adjustment knobs.

4. Check headlight aim (see Adjusting Headlight Aim

in Section 8).

Air Silencer

(CFR/Crossfire/M-Series)

The air silencer is a specially designed component used

to silence the incoming fresh air and also to catch the fuel

that “spits back” out of the throttle body. The throttle

body is calibrated with the air silencer in position; there-

fore, the engine must never be run with the air silencer

removed.

REMOVING

1. Remove the cable tie securing the air intake connec-

tor to the lower air silencer and remove the connec-

tor.

2. Remove the three torx-head screws securing the

belly pan center screen and air intake hold-down tab.

SC077A

3. Remove the screen and air silencer from the front

bumper.

SC084

INSTALLING

1. Place the air silencer into position making sure the

boot is properly seated to the throttle bodies and air

silencer.

2. Install the belly pan center screen; then secure the air

silencer and screen to the front bumper with the

hold-down tab and three torx-head screws.

3. Install the air intake connector and secure the con-

nector to the air silencer with new cable tie.

Air Silencer (Liquid-

Cooled F-Series 2-Stroke)



NOTE: A number of servicing procedures require

that the air silencer be removed and installed. Pay
close attention to the



NOTE: preceding a particular

servicing procedure that will direct the technician to
this section and sub-section for removing/installing
the air silencer.

REMOVING

1. Remove the hood and the left-side and right-side

access panels; then remove the torx-head screws

securing the console.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды