Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 338

Страница: 338 / 535

6-15

ZJ215A

3. Apply Anti-Seize Thread Compound to the threads

of the brake disc retaining nut; then install the nut.

4. With the brake lever in the locked position, use

Brake Disc Socket Wrench to tighten the brake disc

retaining nut to 120 ft-lb.

ZJ237



NOTE: After the retaining nut is tightened to specifi-

cations, peen the nut at the flat spot of the driveshaft.

5. Install the speedometer sensor mounting bracket

(with two spacers); then secure with the two cap

screws. Tighten to 17 ft-lb.

6. If the gear case is installed, secure the driveshaft to

the output shaft with the cap screw (coated with blue

Loctite #243) and washer. Tighten to 70 ft-lb.

742-020A



NOTE: If the gear case is not installed, do not

secure the driveshaft to the output shaft at this time.
Proceed to step 7.

7. Place the resonator into position and secure with the

springs and hairpin clip.

8. Install the skid frame (see Section 7).



NOTE: At this point if the gear case is installed, pro-

ceed to step 22 to finish installing the track drive-
shaft.

9. Place the gear case onto the driveshaft; then press the

gear case toward the sprocket until it properly seats

into place on the chassis. It may be necessary to

rotate the driveshaft slightly for proper seating.



NOTE: Prior to placing the gear case onto the drive-

shaft, apply a light coat of Anti-Seize Thread Com-
pound to the splines of the driveshaft.

10. Secure the gear case by installing the lock nuts; then

using the pattern shown, evenly tighten all the nuts to

20 ft-lb.

742-196B

742-195B

11. Install the torque bumper behind the engine mount-

ing bracket; then carefully work it into place with the

aid of a flat-blade screwdriver.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 338 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: