Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 168

Страница: 168 / 535

2-130

ZJ090B



NOTE: Steps 7-10 are for the non-turbo models

only.

7. Install the throttle bodies and secure with clamps;

then install the throttle cable to the throttle bodies.

ZJ103A

8. Install the left-side upper frame to the chassis by

installing the two cap screws and lock nuts (A)

securing the frame to the front end; then installing

the remaining cap screw and lock nut (B) securing

the upper frame to the skid plate.

ZJ025A

9. Install the five cap screws and lock nuts securing the

upper frame/support gusset to the steering support;

then secure the headlight support bracket to the right-

side upper frame with the two cap screws and lock

nuts. Tighten all lock nuts securely.

ZJ024A



NOTE: Prior to securing the left-side upper frame to

the steering support, make sure the ECU harness is
directed below the upper frame.

10. Install the ECU to the left-side upper frame and

secure with the hold-down strap; then install the

MAP sensor to the bracket.



NOTE: Steps 11-15 are for the turbo models only.

11. Install the flanges to the manifold adapter assembly

and secure with the clamps; then install the manifold

and throttle body assembly and secure with the two

upper clamps.

TZ090A

12. Install the intake hose to the throttle body and slide

the intake pipe into the hose; then secure the pipe to

the cylinder head and cylinder head cover with the

three cap screws. Tighten the two cap screws to the

cover to 18 ft-lb and the remaining cap screw to the

head to 37 ft-lb; then tighten the intake hose clamps

securely.

TZ085B

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 168 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: