Arctic Cat Sno Pro 120 2011 страница 98 Скачать руководство пользователя

Страница: 98 / 535

2-60

CM216



NOTE: At this point, remove all loose hardware to

avoid any falling down into the chassis.

8. Remove the residual coolant from the cylinder/

crankcase water jacket.



NOTE: After draining the coolant, approximately

1.75 fl oz of coolant will remain on both the MAG-side
and PTO-side. To remove the residual coolant, use
the following procedure.

A. Using Vacuum Test Pump or a suitable substitute,

rig the pump to 3/16 in. outside diameter hose.

FC058

B. In turn on each fitting of the crankcase, run the

vacuum pump to purge the cylinder/crankcase

water jacket of the residual coolant.



NOTE: Removing all residual coolant from the cylin-

der/crankcase is critical.

9. Remove the cap screws and nuts securing the cylin-

ders to the crankcase; then using a rubber hammer,

gently tap the cylinders and remove from the crank-

case by lifting them straight up off their studs.

Account for gasket(s) and any alignment pins.

CM217



NOTE: If servicing the MAG-side only, the PTO-side

cylinder must be removed.



NOTE: After the cylinders have been removed,

cover the crankcase to avoid components falling into
the crankcase.

10. Remove the PTO-side piston-pin circlip from the

PTO-side piston; then remove the PTO-side piston-

pin circlip from the MAG-side piston.

11. Using Piston Pin Puller, remove the piston pins from

both pistons.

CM218



NOTE: The piston pins must be removed from the

PTO-side of the piston.



NOTE: For proper assembly, keep all MAG-side

components and all PTO-side components sepa-
rated. Assemble them on their proper sides.

12. Lift the pistons clear of the connecting rods and

remove the small-end connecting-rod bearings

(account for two washers); then remove the piston

rings. Keep each piston with its rings; keep each pis-

ton pin and bearing together as a set.

CAUTION

DO NOT use any type of punch to drive the piston pin
free of the piston; damage may result. Use a piston-pin
puller only.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды