Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 336 / 535

6-13

742-020A



NOTE: If the gear case is being removed, do not

remove the 5/8-in. cap screw. If only the track drive-
shaft is being removed, remove the cap screw and
proceed to step 9.

6. Remove the lock nuts securing the gear case to the

chassis; then remove the remaining lock nut (A)

from the torx-head cap screw.

742-195E

742-196E



NOTE: On the Bearcat Z1/TZ1/Z1 after cap screw

(A) is removed, account for the snubber bracket and
the torx-head cap screw from the back-side of the
chassis.

ZJ308A

7. Place the snowmobile in the upright position; then

using a 5/8-in. socket, long extension, and a hammer,

tap against the driveshaft cap screw until the gear

case is free from the studs of the mounting plate.

8. Remove the cap screw from the inner driveshaft

(from step 5); then remove the gear case.



NOTE: If the gear case is difficult to remove, it may

be necessary to loosen the track tension.



NOTE: On the 2-stroke models, account for the

torque bumper.

9. Remove the hairpin clip and springs securing the res-

onator; then remove the resonator from the engine

compartment.



NOTE: On electric start models, remove the nega-

tive cable from the battery; then remove the positive
cable. Remove the hardware securing the battery to
the tray; then remove the battery.

10. Remove the two cap screws securing the speedome-

ter sensor bracket. Account for two spacers.

ZJ210A

11. Lock the brake lever; then using Brake Disc Socket

Wrench, remove the retaining nut from the drive-

shaft.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды