Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 48 / 535

2-10

CM209A

16. Remove the front cap screws securing the side-plate

brace to the chassis and remove the brace.

CM210A

17. Remove the cap screws (A) and lock nuts (B) secur-

ing the PTO-side engine mounting bracket to the

engine and chassis. Remove the bracket.

742-238A

18. Loosen the cap screw/lock nut (C) securing the

MAG-side engine mounting bracket to the front end.

19. Remove the cap screw and lock nut (D) securing the

engine bracket to the front lower mounting bracket.

20. Disconnect all engine harness connectors.



NOTE: For installing purposes, note the routing of

the harnesses and the location of cable ties.

21. Remove the lower coolant hose; then move the

engine toward the left and up to allow enough room

to remove the remaining coolant hose.

MS382D

CM034C



NOTE: Inspect the engine to ensure all electrical

connectors, hoses, and cables have been removed or
disconnected.

22. Lift the engine out of the engine compartment.

Installing



NOTE: Prior to installing the engine, secure the

MAG-side mounting bracket and the upper right
mounting bracket to the engine with cap screws
(coated with blue Loctite #243) and tighten to 22 ft-lb.

1. Position the engine so the water pump coolant hose

can be installed to the front heat exchanger. Secure

with the hose clamp.

CM034C

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды