Arctic Cat Sno Pro 120 2011 страница 277 Скачать руководство пользователя

Страница: 277 / 535

5-16

2. Pull the recoil starter rope briskly. Meter reading

must be 19.2-23.5V.

INJECTION COIL

1. Test between the two blue/white leads in the four-

prong connector harness from the magneto.

2. Pull the recoil starter rope briskly. Meter reading

must be 15.3-18.7V.

CHARGE COIL (1)

1. Test between the black/red and green/red wires in the

triple-plug connector from the magneto.

2. Pull the recoil starter rope briskly. Meter reading

must be 30.2-36.9V.

CHARGE COIL (2)

1. Test between the brown/white and green/red wires in

the triple-plug connector from the magneto.

2. Pull the recoil starter rope briskly. Meter reading

must be 32.0-39.1V.

IGNITION TIMING SENSOR
(1 and 2)

1. Test between the green/white and brown/green wires

in the connector from the sensors.

2. Pull the recoil starter rope briskly. Meter reading

must be 4.3V (1) or 4.4V (2).

PRIMARY COIL (MAG/PTO)

1. Connect the red meter lead to the orange/red wire

(MAG) or to the white/red wire (PTO); then connect

the black meter lead to the orange/black wire (MAG)

or to the white/black wire (PTO).

2. Pull the recoil starter rope briskly. Meter reading

must be 172-233V.

LIGHTING COIL

1. Connect the red meter lead to one yellow wire; then

connect the black meter lead to another yellow wire.

2. Pull the recoil starter rope briskly. Meter reading

must be 5.4-5.8V.

LIGHTING COIL (

2000 RPM)

1. Attach the red maxiclip to the yellow lead; then

attach the black maxiclip to the brown lead.

2. Connect the red meter lead to the red maxiclip; then

connect the black meter lead to the black maxiclip.

3. With the rear of the snowmobile on a shielded safety

stand, run the engine at 2000 RPM.

4. Meter reading must be 14.8-22.2V.

Testing Low-Oil Light

Sensor

The low-oil light sensor is a magnetic switch. Its opera-

tion is based on a magnet located around the inside diam-

eter of a 1/2-in. hole in a plastic float. The switch located

in the stem of the sending unit is positioned through the

hole in the float. When the float drops to the lower part of

the stem, the magnet closes the electrical contacts

(located in the stem) allowing the current to pass on to

the warning light.

If the sensor should fail, it must be replaced. To test the

sensor, use the following procedure.

1. Remove the sensor from the oil reservoir by twisting

and pulling upwards. Wipe excess oil from the sensor.

2. Unplug the sensor from the wiring harness.

3. Set the meter selector to the OHMS position.

4. Touch each of the meter leads to one of the two wires

coming from the sensor. With the sensor in its nor-

mal position (float end down), the meter should read

resistance.

5. If the meter reads no resistance, check to make sure

good contact has been made with each of the wires

coming from the sensor. If the meter still reads no

resistance, replace the sensor.

6. While maintaining contact between the meter leads

and the sensor, raise the float. The meter must read

no resistance. If the meter reads resistance, replace

the sensor.

7. If the sensor tested out satisfactory but the light

doesn’t illuminate with only a small amount of oil in

the reservoir, check the bulb.

8. If the bulb is in good condition, check for voltage at

the connection where the sensor plugs into the acces-

sory wiring harness. Using a multimeter set on the 50

ACV scale, start the engine and allow it to idle.

Touch the red lead of the voltmeter to the red wire in

the two-prong connector. Touch the black lead to the

black wire in the wiring harness. At idle, the meter

should read 5 to 6 volts (AC). If no voltage is present

but the lights on the snowmobile operate normally,

either check the wiring harness for a broken wire or

replace the harness.

Testing Coolant

Temperature Sensor

1. Disconnect the main wiring harness connector from

the temperature sensor.

2. Connect an ohmmeter between the sensor terminal

and any convenient chassis ground (or any brown

wire). The ohmmeter must read less than 20 ohms of

resistance with the coolant temperature more than

+230°F. The ohmmeter must read no resistance with

the coolant temperature less than +190°F.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды