Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 43 / 535

background image

2-5

2

FZ013

4. Route the wiring harness as noted during disassem-

bly and connect the plug-ins to the CDI and ignition

coil; then connect the main harness plug-in.



NOTE: Prior to connecting the harness, clean all

plug-ins with contact cleaner and apply Dielectric
Grease to the connectors.

5. Connect the oil line to the oil-injection pump and

secure with the clamp; then with the oil-injection

pump cable properly routed, install the cable to the

oil-injection pump and secure with the washer and E-

clip.



NOTE: Verify the mark on the control arm is aligned

with alignment mark on the oil-injection pump boss
in the full-open position. If the marks are not aligned,
adjust synchronization by loosening the jam nuts on
the adjuster. Rotate the jam nuts/adjuster nut until
proper alignment is attained. Tighten jam nuts.



NOTE: When the cable/linkage adjusting nut is

adjusted correctly, the throttle lever will move approx-
imately 1/8 in. before the oil-injection pump arm
begins to move.

6. Remove the oil bleed plug from the oil-injection

pump. When oil flows from pump free of air bubbles

and the hose is full of oil, install the oil bleed plug

and tighten.



NOTE: Place a cloth beneath the oil-injection pump

to contain any oil spilled during the bleeding process.

7. With the throttle cable and fuel lines properly routed,

install the flange clamps to the intake flanges; then

install the carburetors and secure with the clamps.

FZ006

8. Install the headlight support bracket and secure the

bracket with the cap screws and lock nuts.



NOTE: The headlight support bracket must be

installed before the engine is secured.

9. Install the rear MAG-side engine mounting bracket

to the engine with the three cap screws (C). Tighten

to 20 ft-lb; then position the engine to the chassis

mounts.

0743-921

10. Install the snubber bracket; then secure the bracket to

the chassis with the cap screws and lock nuts (D).

Tighten to 20 ft-lb.

11. Install the three lock nuts (B) securing the engine

plate to the chassis and tighten to 20 ft-lb; then install

the cap screw (A) securing the rear MAG-side

engine bracket to the chassis. Tighten to 20 ft-lb.

12. Carefully work the carburetor boots over the intake

bore of the carburetors; then install the PTO-side

starter motor bracket to the engine and secure with

the two cap screws (B). Tighten to 20 ft-lb.

FZ023A

13. With the rubber dampers in place on the brackets,

install the starter motor and the MAG-side bracket to

the engine with the two cap screws (A) and tighten to

20 ft-lb. Route the ground cable up through the engine

plate and secure with cap screw. Tighten securely.

Manual

Table of Contents

«
...
41
42
43
44
45
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды