Arctic Cat Sno Pro 120 2011 страница 247 Скачать руководство пользователя

Страница: 247 / 535

4-21

2. Suspend the sensor (only up to the threads) in a

container filled with automatic transmission oil;

then slowly heat the oil on a hot plate.

3. Using a fluid thermometer, closely monitor the oil

temperature, and using a digital multimeter with

the leads connected to the sensor leads, observe

the resistance reading.

4. The sensor must read resistance and must be

within the temperature range (see chart).

5. If the resistance and temperature are not within

specifications, replace the sensor.



NOTE: Before replacing the sensor, repeat the test

to confirm results.

Throttle Body

Assembly

REMOVING (500/600/800/1000 cc)



NOTE: The expansion chamber and air silencer

must be removed for this procedure (see Section 3).

1. Disconnect the wiring harness from each injector and

from the throttle position sensor connector.

2. Remove the coolant hoses from the throttle body

assembly and plug them to prevent leakage.

3. Remove the fuel supply hose from the fuel rail.

4. Loosen the flange clamps.

5. Slide the throttle body assembly out of the flanges;

then loosen the jam nut securing the throttle cable

and remove.

6. Where applicable, remove the oil pump control rod.

7. Remove the throttle body assembly.

INSTALLING
(500/600/800/1000 cc)

1. Attach the throttle cable to the throttle body. Secure

with jam nut.

2. Place the throttle body assembly into position. Make

sure the flanges and boots are positioned properly.

Secure with flange clamps.

3. Where applicable, connect the oil pump control rod.



NOTE: The coolant hoses must be connected first;

then the throttle body assembly must be installed.

4. Secure the coolant hoses to throttle body assembly.

5. Connect the fuel supply hose to the fuel rail.

729-325A

6. Connect the wiring harness to each injector and

throttle position sensor.



NOTE: Install the air silencer and the expansion

chamber (see Section 3).

7. Place the rear of the snowmobile on a shielded safety

stand and start the engine without touching the throt-

tle. It may idle slowly and stop. Restart using the

same procedure until the engine starts and builds

RPM on its own.

8. Check the cooling system.

9. Adjust the throttle cable as necessary.

REMOVING/DISASSEMBLING
(1100 cc Non-Turbo)



NOTE: To remove the throttle body assembly, it will

be necessary to remove the air silencer. Proceed to
Section 3 - Air Silencer (1100 cc Non-Turbo) sub-sec-
tion and follow steps 1-12 of REMOVING.

1. Remove the coolant hoses and MAP sensor hoses

from the throttle body.

° F

° C

ohms

219.6

122

238.5

212

100

275.9

302

150

312.7

CAUTION

Since the fuel supply hose may be under pressure,
remove it slowly to release the pressure. Place an
absorbent towel around the connection to absorb fuel.

CAUTION

These hoses must be connected to the correct fittings.

CAUTION

When installing the throttle bodies, make sure the
gasline hose is properly routed to avoid premature
wear and/or contact with exhaust components.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды