Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 110 / 535

2-72

0742-304

22. Noting the alignment dots, install the thermostat

housing with thermostat. Secure the housing with

cap screws and tighten to 96 in.-lb.

FC078A

FC073

23. With new gaskets, install the reed valve assemblies;

then secure the intake flanges to the crankcase.

Tighten in a crisscross pattern to 96 in.-lb.

24. Install the dowel pins into the crankcase; then place

the cylinder base gasket into position on the crank-

case.

25. Install the piston rings on each piston so the letter on

the top (inclined surface) of each ring faces the dome

of the piston.

726-306A

26. Apply oil to the connecting-rod small end bearings;

then install the small-end bearings. Install a washer

on each side of the connecting rod.

TZ068



NOTE: The shoulder side of the washer must seat to

the needle bearing.

FC075

27. Place each piston over the connecting rod so the indi-

cator dot on each piston will point toward the intake/

exhaust ports; then secure with an oiled piston pin.



NOTE: The indicator dot is found on the piston

dome top.

CAUTION

Incorrect installation of the piston rings will result in
engine damage.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды