Arctic Cat Sno Pro 120 2011 страница 429 Скачать руководство пользователя

Страница: 429 / 535

7-61

CM232

6. Turn the slide rail onto the side the idler wheel was

installed in (from step 5); then with a block of wood

placed under the inner carriage axle/idler arm, install

a wave washer.

CM238A

7. Install the remaining idler wheel along with the snap

ring onto the axle; then using a suitable driving tool,

carefully drive the snap ring into the idler wheel until

properly seated in the groove of the axle.

CM239

8. Grease the idler arm and rear arm grease fittings with

a low-temperature grease.

Front Arm Assembly



NOTE: The skid frame must be removed for this pro-

cedure (see Removing Skid Frame in this sub-sec-
tion), and the rear springs must be removed from the
adjusting cams.

REMOVING

1. Remove the cap screws and lock nuts securing the

rear arm shock absorber and shock link to the front

arm pivot and account for the sleeves.

CM233A

2. Remove the cap screws and lock nuts securing the

limiter straps to the front arm. Account for flat wash-

ers.

CM240A

3. Remove the cap screw and lock nut securing the

shock absorber to the front arm. Pull the shock eyelet

free of the bracket. Account for a serrated axle.

CM241

4. Remove the cap screws and lock nuts securing the

front arm to the slide rails.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды