Arctic Cat Sno Pro 120 2011 страница 57 Скачать руководство пользователя

Страница: 57 / 535

2-19

CM135A

5. Raise the PTO-side of the engine and support the

engine in this position. Connect the coolant tank

hose to the bottom left outlet on the engine and

secure with the hose clamp.

CM136A

6. With the torque bumper positioned against the gear

case, install PTO-side engine mounting bracket to

the engine with cap screws (coated with blue Loctite

#243) and to the chassis with lock nuts. DO NOT

TIGHTEN AT THIS TIME.

7. From step 6, tighten the PTO-side mounting bracket-

to-engine cap screws (D) (coated with blue Loctite

#243) to 24 ft-lb; then tighten the lock nuts (C)

securing the mounting bracket to the chassis (from

step 6) to 20 ft-lb.

8. Tighten the MAG-side engine mounting bracket-to-

chassis cap screw and lock nut (A) (from step 3) to

20 ft-lb and the front lower mounting bracket cap

screw and lock nut (B) (from step 3) to 30 ft-lb.

9. Before connecting the wiring harness plug-ins, clean

the connectors and apply Dielectric Grease; then

connect all electrical wiring harness plug-ins making

sure all wiring and coolant hoses are routed properly

as noted in removing. Install the wiring harness

wrap.



NOTE: Use cable ties to secure the wiring har-

nesses as necessary.

10. Place the recoil starter into position and secure the

starter with five cap screws. Tighten in a crisscross

pattern to 96 in.-lb.

CM137

11. Tighten the spark plugs to 19 ft-lb; then connect the

plug wires and on the 800 cc, the knock sensor plug-in.

CM130A

12. If removed, connect the oil-injection control rod to

the oil-injection pump and secure.

CM028A

13. Route the oil-supply hose through the hole in the

chassis with the rubber grommet and to the oil pump.

Secure with the clamp.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды