manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 266 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 266

5

5-5

2. To determine which switch needs adjusting, discon-

nect both carburetor safety switches from the main

wiring harness connector.

3. Connect a digital ohmmeter to one carburetor safety

switch connector; then compress the throttle lever

while observing the meter reading and measure the

gap between the throttle lever and control housing at

the moment the meter reading changes from open to

closed. Repeat this step for the other carburetor

safety switch.

NOTE: The correct throttle lever/control housing

gap is a range of 0.375-0.500 in. the moment the
meter reading changes from open to closed. A switch
that changes from open to closed before the other
one is the switch that must be raised to attain safety
switch synchronization.

742-349A

4. If an adjustment is necessary, loosen the switch

bracket screws, move the switch up, tighten the

screws, and then reset using step 3.

NOTE: After completion of any adjustments, throttle

lever “side pressure” should not cause an ignition
miss at idle. Carburetor switches set too low or an
excessively tight throttle cable makes the shutdown
system very sensitive to throttle lever “side pres-
sure” near idle. To test carburetor safety switch syn-
chronization, follow steps 5-9.

5. Reconnect the carburetor safety switch connectors.

Place the rear of the snowmobile on a shielded safety

stand; then start the engine and allow it to warm up

for 3-4 minutes.

6. Hold both the top and bottom of the throttle lever pin

so that depression of the throttle lever does not move

the lever pin in its control slot.

0728-916

7. Slowly depress the throttle lever to increase engine

RPM.

NOTE: Engine RPM must be allowed to increase

slowly.

8. Observe the tachometer and the drive clutch to deter-

mine the moment the carburetor safety switches shut

down the ignition. Since retaining the throttle lever

pin prevents the switch in the throttle control housing

from closing, the carburetor safety switches should

shut down the ignition at or slightly after clutch

engagement.

9. Repeat steps 6-8 several times. If ignition shutdown

always occurs at or slightly after clutch engagement,

the carburetor safety switches are synchronized.

10. To complete the procedure, repeat step 1.

NOTE: After completion of any adjustments, throttle

lever “side pressure” should not cause an ignition
miss at idle. Carburetor safety switches set too low or
an excessively tight throttle cable makes the shut-
down system very sensitive to throttle lever “side
pressure” near idle.

Throttle Position Sensor 

(2-Stroke EFI Models)

NOTE: Engines equipped with throttle position sen-

sor have a protective feature called “fail-safe” igni-
tion timing preventing engine damage should the
TPS fail. If the TPS does fail, the engine may run nor-
mally at low RPM but will run poorly at high RPM
allowing the operator to get the snowmobile to safety
with no engine damage. The engine will continue to
operate this way until the TPS is adjusted or
replaced.

NOTE: Ignition timing specifications are located on

the Electrical Specifications Chart in Section 1 of this
manual.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов