Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 269 / 535

5-8

1. Using Throttle Position Sensor (TPS) Adjustment

Tool Kit, connect its wiring harness to the TPS. Con-

nect the red tester lead to the white adjustment tool

jack; then connect the black tester lead to the black

adjustment tool jack.

2. Ensure that the throttle cable has the proper amount

of free-play.

3. With the throttle in the idle position, compare the

reading on the voltmeter to the chart. If the reading is

within prescribed specification, proceed to step 4.

4. Compress the throttle lever slowly to the full-open

position. The meter reading should show a smooth

rise in voltage all the way to the full-open throttle

position. If the voltage seems to be erratic or doesn’t

meet the prescribed specification, repeat this proce-

dure several times to confirm results.



NOTE: If at any point throughout the throttle range

the meter reads no voltage (open), hold the throttle
lever in that position. If the voltage does not return,
the throttle body must be replaced.

5. If the full-open throttle voltage remains erratic or out

of specification, proceed to Adjusting TPS.

6. If the TPS is within the prescribed specification, dis-

connect the adjustment tool harness from the TPS.

Connect the snowmobile TPS harness to the TPS.



NOTE: Before installing the TPS harness connector,

apply dielectric grease to the connector pins.

ADJUSTING TPS



NOTE: Adjusting the TPS is for out of warranty

snowmobiles only.



NOTE: The throttle shaft must be against the throt-

tle stop for this procedure.

1. Disconnect the harness connector from the TPS.

2. Loosen the screw(s) of the throttle position sensor to

allow adjustment.

3. Using Throttle Position Sensor (TPS) Adjustment

Tool Kit, connect its wiring harness to the TPS. Con-

nect the red and black digital voltmeter leads to the

white and black jacks of the TPS adjustment tool.

4. While observing the digital voltmeter, slowly rotate

the sensor until idle voltage specification is observed

on the LCD of the multimeter. While holding the

sensor in this position, tighten the screw(s) securing

the sensor to the throttle body securely.

5. Gently snap the throttle open and closed several

times to check the TPS voltage. If it has changed

from the idle voltage specification, loosen the

screw(s) securing the sensor and make necessary

adjustments.

6. With the idle position set to specification, compress

the throttle lever to the full-open position. The full-

open specification should be observed. Gently snap

the throttle lever open and closed several times and

note if the reading remains within the specification.



NOTE: If, after adjusting the Throttle Position Sen-

sor to the IDLE specification, the FULL-OPEN is less
than 4.30 volts, recheck the IDLE setting. If the IDLE
setting is correct, replace the sensor.

REPLACING TPS



NOTE: Replacing the TPS is for out of warranty

snowmobiles only.

Removing

1. Disconnect the throttle cable from the throttle pul-

ley.

2. Disconnect the TPS wiring harness from the TPS;

then noting the position of the TPS, remove the

screw(s) securing the TPS to the throttle body hous-

ing and remove the sensor. Account for the O-ring

fitting into the groove of throttle body.

Installing

1. Apply a light coat of silicone grease to the area

around the outside of the TPS flange and into the O-

ring groove. Install the O-ring into the groove.

2. Install the new TPS onto the throttle shaft by align-

ing the “flats” on the throttle shaft cam with the

alignment points of the sensor; then rotate the sensor

until properly positioned on the throttle body.

ZJ254A

Engine

Idle

Full-Open

1100 cc Non-Turbo

1.10-1.14

4.30-4.50

1100 cc Turbo

0.69-1.11

4.00-4.20

CAUTION

Never adjust the throttle plate stop screw and nut. The
idle circuit is controlled by the ISC valve.

Engine

Idle

Full-Open

1100 cc Non-Turbo

1.10-1.14

4.30-4.50

1100 cc Turbo

0.69-1.11

4.00-4.20

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды