manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 526 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 526

8-36

2. Connect the fuel hose and the fuel pump two-wire

connector; then install the two remaining lock nuts

securing the gas tank to the tunnel.

3. Install the console (see the appropriate Console in

this section).

4. On the CFR/Crossfire, place the seat into position

and secure with the latches inside the storage com-

partment.

5. On the M-Series, place the seat into position over the

studs of the gas tank/chassis; then secure the seat

with two washers and lock nuts.

Gas Tank/Seat Assembly 

(Bearcat/F-Series/T-Series/

Z1)

0741-965

REMOVING

1. Remove the hood and open the right-side and left-

side access panels.

2. Remove the two torx-head cap screws (A) securing

the console to the chassis; then lift up the rearward

end of the console and disconnect the console har-

ness plug-in. Remove the console.

3. Remove the two torx-head cap screws (B) securing

the handlebar close-off panel; then remove the three

torx-head cap screws (C) securing the rear side pan-

els (spars) to the seat support tubes. 

4. Remove the two screws (D) securing the knee pads

to the gas tank; then remove the remaining body

screws securing the knee pads to the steering sup-

port.

5. On the standard models, push down on both seat

retainer brackets (located in the rear storage com-

partment) and remove the seat.

NOTE: On the LXR/Sno Pro/Z1/TZ1 LXR models,

adjust the seat to the lowest position; then while lift-
ing on the top forward part of the seat, remove the
machine screw (E) from the right side of the seat sup-
port assembly. Remove the seat.

NOTE: On the TZ1 standard, remove the two torx-

head cap screws securing the seat frame to the tun-
nel.

6. Remove the four cap screws (F) securing the support

tubes to support plate.

7. Remove the six torx-head screws (G) securing the

seat support assembly to the tunnel; then slide the

support back out of the way.

ZJ010A

8. Disconnect the fuel pump four-wire connector; then

slide the gas tank rearward enough to gain access to

the gasline hose connector.

FS261A

9. Compress the clip on the gasline hose connector and

remove the hose from the gas tank; then disconnect

the gas tank vent hose and close off the vent hose

outlet of the gas tank and remove the gas tank.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов