manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 333 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 333

6-10

0744-549

CORRECTING OFFSET

1. To correct offset, the driven pulley must be moved

laterally on the input shaft. Remove the cap screw

and washers securing the driven pulley.

NOTE: If the driven pulley is tight on the shaft, pull

the driven pulley off using the Driven Pulley Puller.

2. To move the driven pulley inward on the shaft,

remove alignment washer(s) from the gear case side

of the pulley.

3. To move the driven pulley outward on the shaft,

install additional alignment washer(s) on the gear

case side of the pulley.

4. Arrange washers to obtain correct offset; then install

driven pulley, cap screw, and washers and tighten to

32 ft-lb.

CHECKING PARALLELISM
(800/1000/1100 cc)

1. Remove the drive belt; then open the driven sheaves

and place Clutch Alignment Bar (Parallelism)

between the sheaves. Release the sheaves.

2. Check the parallelism of the drive clutch/driven pul-

ley using the parallelism bar and reference points X

and Y with the parallelism bar between the driven

sheaves. Using a caliper or a machinist’s scale, mea-

sure X and Y from the back side of the parallelism

bar to the back side of the drive clutch sheave. Mea-

surement Y must be 0.060 in. ± 0.020 in. more than

measurement X, but Y must not exceed measure-

ment X by more than 0.100 in. 

0744-609

3. If parallelism is not within specifications, the paral-

lelism must be corrected by first loosening all the

engine mounting bolts (left side, front, and right top

rear). Then, pry the front of the engine towards the

MAG-side of the engine compartment. Next tighten

the left-side mounting bolts followed by the front

and right-top rear bolts. Re-check the parallelism. If

still out of specification, repeat correction procedure.

CORRECTING PARALLELISM

The following correcting procedure is for the 800/1000

cc models only.

NOTE: This procedure should be done only as nec-

essary.

1. Remove the drive clutch and the driven pulley; then

loosen the engine mounting hardware in the

sequence shown (see appropriate illustration).

0743-438

0743-437

2. Using a 2x4 block of wood tapered at each end, drive

the block between crankshaft and the input shaft until

the engine has visibly moved forward (see illustration).

CAUTION

Do not apply Loctite to the cap screw or damage to the
gear case will occur.

CAUTION

Do not allow the driven pulley to “float” on the input
shaft. Damage to the driven pulley will occur. 

Crossfire/M-Series

F-Series

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов