Arctic Cat Sno Pro 120 2011 страница 82 Скачать руководство пользователя | Manualshive

Страница: 82 / 535

background image

2-44

A932

CRANKSHAFT



NOTE: If any servicing of the connecting rods, cen-

ter bearings, or oil-injection pump drive gear is nec-
essary, Arctic Cat recommends the crankshaft be
taken to a qualified machine shop for that service.

1. Wash the crankshaft with bearings in parts-cleaning

solvent.

2. Inspect the bearings for wear, scoring, scuffing, dam-

age, or discoloration. Rotate the bearings. Bearings

must rotate freely and must not bind or feel rough. If

any abnormal condition is noted, replace the bearing.

FC039

3. Inspect the connecting-rod bearings by rotating

them. The bearings must rotate freely and must not

bind or feel rough. If a connecting-rod bearing must

be replaced, the connecting rod and crank pin must

also be replaced.

FC040

4. Inspect the oil-injection pump drive gear for any

signs of worn or chipped teeth. If either condition

exists, replace the gear.



NOTE: Lubricate bearings thoroughly prior to

assembly.

REMOVING OUTER CRANKSHAFT
BEARINGS



NOTE: Steps 1-2 are for removing the MAG-side

bearing.

1. Place the crankshaft in a suitable support; then install

Crankshaft Bearing Remover between the journal

and the MAG-side bearing.

2. Place the protective cap on the crankshaft end; then

remove the bearing from the end of the crankshaft.

Account for any shim(s). Note the position of the

dowel pin hole.

AN068D

3. The PTO-side bearing may be removed simply by

sliding the bearing off the PTO end.

AN151A

4. Inspect the crankshaft bearing area for wear. If any

wear is noted on either end, replace the crankshaft

end.

INSTALLING OUTER CRANKSHAFT
BEARINGS



NOTE: Steps 1-3 are for installing the MAG-side

bearing.

1. Wrap a thick towel around the crankshaft; then

secure the crankshaft vertically in a vise.

Manual

Table of Contents

«
...
80
81
82
83
84
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

2014 XF 2-STROKE

Бренд: Arctic Cat Страницы: 196

2011 Crossfire 600

Бренд: Arctic Cat Страницы: 56

Бренд: BOMBARDIER Страницы: 4

ski-doo MX-Z Blair MORGAN

Бренд: BOMBARDIER Страницы: 14

Бренд: BOMBARDIER Страницы: 17

ski-doo Tundra Scandic 2004 Series

Бренд: BOMBARDIER Страницы: 427

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды