Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 332 / 535

6-9

FS093

5. With the pulley in place on the compressor, install

the compressor flange spacer and wing nut; then

compress the driven pulley spring.

CM069

6. Install the torx-head cap screws securing the mov-

able sheave. Tighten in a crisscross pattern to 72 in.-

lb.

CM061

7. Remove the pulley from the compressor.

INSTALLING

1. Set the brake lever lock.

2. Install the alignment washers; then install the driven

pulley onto the input shaft. Tighten to 32 ft-lb.

CM125A

3. Check drive clutch/driven pulley alignment.

4. Install the drive belt.



NOTE: For installing drive belt, see Drive Belt in this

section.

Drive Clutch/Driven Pulley

If premature drive belt wear is experienced or if the drive

belt turns over, parallelism/offset must be checked. Also,

parallelism/offset must be checked whenever either the

drive clutch or driven pulley is serviced. To check offset,

use appropriate Clutch Alignment Bar. To check parallel-

ism, use Parallelism Bar.

CHECKING OFFSET

1. Open the left-side access panel; then remove the belt

guard.

2. Install Clutch Alignment Bar between the drive

clutch sheaves.

3. Allow the bar to rest on the drive clutch shaft and

against the outside edge of the driven pulley station-

ary sheave.



NOTE: The alignment bar must extend beyond the

front edge of the drive clutch.

4. With the bar against the outside edge of the driven

pulley stationary sheave at points A and B, the bar

should just clear the inside edge of the stationary

sheave of the drive clutch and rest on the stationary

shaft at point C. If the bar either will not clear the

inside edge or is more than the specified amount, the

offset must be corrected.

CAUTION

Do not allow the driven pulley to “float” on the input
shaft. Damage to the driven pulley will occur.

CAUTION

Do not apply Loctite to the cap screw or damage to the
gear case will occur.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды