Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 473

Страница: 473 / 535

7-105

TZ049

2. Secure the track adjuster bracket with the cap screws

and lock nuts. Tighten to 120 in.-lb.

3. Secure the front arm to the slide rail with the cap

screws and lock nuts. Tighten to 40 ft-lb.

TZ050



NOTE: At this point, return to step 1 and tighten the

rear arm and front arm cap screws and lock nuts to
40 ft-lb; then tighten the rear arm pivot/idler wheel
assembly to 20 ft-lb.

4. Install coupler block w/bushing. Secure with cap

screw and lock nut. Tighten securely.

TZ046A

5. Install the adjuster bushing and rear idler wheel.

Install a cap screw and flat washer. Tighten only until

snug.



NOTE: Care must be taken that the adjuster bushing

slot with the hole is aligned properly with the adjuster
bolt.

TZ045A



NOTE: Tighten the rear idler wheel axle only until

snug until the skid frame is installed and track ten-
sion is adjusted; then the axle assembly must be
tightened to 20 ft-lb.

6. Install the rear arm limiter and secure with the cap

screw. Tighten the cap screw (coated with blue Loc-

tite #243) to 50 ft-lb.

TZ051

7. Install the overload spring tension block with a cap

screw and lock nut. Tighten securely.

TZ052

8. Place the overload spring with retaining clips and

bushing to the proper hole in the slide rail.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 473 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: