Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 216 / 535

background image

3-37

3

REMOVING

1. Remove the hood and the right- and left-side access

panels.

2. Remove the two torx-head cap screws (A) securing

the console to the chassis; then lift up the rearward

end of the console and disconnect the console har-

ness plug-in. Remove the console.

743-850A

3. Remove the torx-head cap screws and lock nuts (B)

securing the right-side front and rear spar panels

together; then remove the two torx-head screws (C)

securing the front spar panel to the front bumper.

4. Loosen the intercooler hose clamps at the intake pipe

and the turbocharger; then carefully work the inter-

cooler upward until it releases from the rubber grom-

mets.

5. Disconnect the exhaust springs and remove the center

exhaust pipe from between the exhaust manifold and

resonator; then secure the pipe up and out of the way.

6. Remove the cap screw (A) securing the air silencer

to the right-side upper frame; then loosen the hose

clamp (B) and disconnect the air silencer from the

turbo inlet.

TZ058A

7. Using a suitable clamping device, clamp off the cool-

ant return hose; then remove the clamp securing the

coolant return hose to the return line of the turbo-

charger. Remove the hose.

TZ060A

8. Remove the four cap screws securing the upper heat

shield to the turbo outlet and exhaust manifold.

TZ061

CAUTION

Do not carry the turbocharger by the hoses or by the
waste gate control rod. Damage could occur.

CAUTION

Do not run a turbocharged engine with the intake hose
removed from the compressor inlet. Dirt, foreign
objects, or loose clothing can be ingested causing tur-
bocharger failure and engine damage.

CAUTION

Do not spin the turbo with compressed air as bearings
will be damaged.

CAUTION

Do not store the turbo vertically as oil will be lost from
the bearing cavity and bearing damage on start-up
could occur.

CAUTION

Do not remove sealing tape or plastic from the turbo
until ready for installation. Damage could occur.

CAUTION

Do not allow dirt or foreign objects to fall into the tur-
bocharger. Damage could occur.

CAUTION

If the turbocharger is not being replaced during this
procedure, close off the inlet and outlet of the turbo to
avoid any foreign objects from entering the turbo-
charger.

CAUTION

Make sure the washers are free from the heat shield
cap screws or damage to the heat shield will occur.

Manual

Table of Contents

«
...
214
215
216
217
218
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

600 INDY VOYAGEUR

Бренд: Polaris Страницы: 136

800 PRO-RMK 2011

Бренд: Polaris Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды