Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 418 / 535

7-50

FZ064



NOTE: The adjusting bolt may have to be loosened

to remove the adjuster bushing.



NOTE: At this point, the slide rail should be free of

the skid frame components and can be removed.

10. Remove the cap screws and lock nuts securing the

track adjuster bracket.

MS193A



NOTE: If the shock pads must be replaced, refer to

Shock Pads at the beginning of this procedure.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the slide rail for cracks (A), elongated holes

(B), or unusual bends.

MS220A

2. Inspect the wear strip for wear. The wear strip must

be 0.42 in. thick or thicker. If the wear strip measure-

ment is less than specified, replacement of both wear

strips is necessary.

0743-189

INSTALLING

1. Secure the track adjuster bracket with the cap screws

and lock nuts. Tighten to 120 in.-lb.

MS193A

2. Place the rail into position; then install the adjuster

bushing and rear idler wheel. Install a cap screw and

flat washer. Tighten only until snug.

CM261A



NOTE: Care must be taken that the adjuster bushing

slot with the hole is aligned properly with the adjuster
bolt.



NOTE: Tighten the rear idler wheel axle only until

snug until the skid frame has been installed and track
tension has been adjusted; then the axle assembly
must be tightened to 40 ft-lb.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды