Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 379

Страница: 379 / 535

7-11

4. Inspect the cap screw for cracked, stretched, or dam-

aged threads. Use a new lock nut when assembling.

INSTALLING

1. Position the end cap on the slide rail; then align the

hole in the end cap with the hole in the slide rail.

2. Secure with a cap screw, washers, and lock nut.

Tighten to 80 in.-lb.

Shock Pads



NOTE: The skid frame does not have to be removed

for this procedure.

REMOVING



NOTE: The shock pads should be removed only if

being replaced.

1. Using a 3/16-in. drill bit, drill out the rivets securing

each front shock pad to the slide rail. Account for the

retaining brackets.

2. Remove the torx-head screws and lock nuts securing

the rear shock pads to the slide rail; then remove the

shock pads.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the pad and retaining brackets for damage or

wear.

2. Inspect the rivet holes in the slide rail for damage or

elongation.

INSTALLING

1. Place the front and rear pads and retaining brackets

into position on the slide rail.

2. Secure the pads with rivets.

AG531D

Idler Wheels/Mounting

Blocks



NOTE: The skid frame does not have to be removed

for this procedure.

REMOVING

1. Remove the cap screws and lock nuts securing the

front outer idler wheel and the idler wheel mounting

block. Account for flat washers and two shim wash-

ers (if applicable).

MS002B

MS003A

2. If applicable, note the locations of the shim washers

for assembly purposes. The shim washers are to be

installed to the inside of the idler wheels.

MS004



NOTE: On the idler wheels with inserts or idler

wheels with a non-removable bearing, account for a
spacer.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 379 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: